FlyingPole UltraGrip3 Instructions
1.0 PACKAGE APPEARANCE
1 cardboard tube containing the two pole sections with the webbing already threaded through.
2.0 PACKAGE CONTENTS
1 lower pole section with spherical lower end cap.
1 upper pole section with upper end cap for webbing exit.
1 central joint to connect the two pole sections, suitable for the passage of the webbing.
1 webbing, length 325 cm (22 kN breaking strength).
1 5 mm Allen key.
1 4 mm Allen key.
1 10 mm wrench.
1 instruction sheet with QR code.
2.1 TOOLS REQUIRED FOR INSTALLATION, NOT INCLUDED
To use the FlyingPole UltraGrip3, a swivel is required to prevent the webbing from twisting. If this has not already been installed, you can purchase our Albatros plate with integrated swivel here: Albatros - anchor plate for ceiling with built-in swivel
Accessories required to install the FlyingPole to the ceiling using the Albatros plate, equipped with integrated swivel:
- n° 1 rope or Daisy Chain to connect the FlyingPole to the ceiling if it is not connected directly to the Albatros.
- n° 2 carabiners.
Accessories required to install the FlyingPole to the ceiling without using the Albatros plate:
- n° 1 ceiling hook.
- n° 1 rope or Daisy Chain to connect the FlyingPole to the ceiling if it is not connected directly to the ceiling.
- n° 1 swivel, allowing the pole to rotate without twisting the ropes.
- n° 2 carabiners.
3.0 POLE ASSEMBLY
The pole is shipped with the webbing already inserted to speed up installation.
Take care when unpacking the pole and components to avoid damaging the pole coating.
Pole assembly operations must be carried out on the ground.
Place the pole sections horizontally on the ground and kneel in front of them to begin assembly.
In case of doubt, contact support by email at
If you need to assemble the FlyingPole UltraGrip3 completely, for example to replace the webbing, go to section 4.0.
3.1 JOIN THE POLE SECTIONS AND TIGHTEN THE CENTRAL JOINT SCREWS FIRMLY
1° Place the sections on the ground and join them, making sure to align the holes and paying attention to the correct positioning of the webbing in the dedicated grooves of the joint.
2° Using the 5 mm Allen Key, tighten the joint by screwing it clockwise very firmly. WARNING: do not pinch the webbing between the joint and the pole.
WARNING!!! Before each use, check that all joints are properly tightened.
2° Using the 5 mm Allen Key, tighten the joint by screwing it clockwise very firmly. WARNING: do not pinch the webbing between the joint and the pole.
WARNING!!! Before each use, check that all joints are properly tightened.
THE POLE IS ASSEMBLED. YOU CAN NOW PROCEED WITH INSTALLATION
Hang the FlyingPole UltraGrip3 using the webbing at the upper end, making sure that the type of connector is compatible with use on textile products.
It is recommended to keep the FlyingPole UltraGrip3 working height as low as strictly necessary and to use appropriate ground protection equipment.
It is recommended to check that there are no obstacles or objects within the operating and swinging range of the FlyingPole UltraGrip3.
It is recommended to keep the FlyingPole UltraGrip3 working height as low as strictly necessary and to use appropriate ground protection equipment.
It is recommended to check that there are no obstacles or objects within the operating and swinging range of the FlyingPole UltraGrip3.
4.0 REPLACING THE WEBBING AND COMPLETE POLE ASSEMBLY
These instructions explain how to replace the webbing and fully assemble the FlyingPole UltraGrip3.
The webbing must be replaced periodically and/or in case of damage or wear.
WARNING: the webbing supplied by the company with the product is manufactured according to specific technical requirements and a defined breaking load. Replacing it with unsuitable or low-quality rope or webbing may cause accidents and serious injuries.
The webbing used to anchor the Flying Pole to the ceiling must be original or have suitable characteristics for human suspension (22kN).
For information and to purchase original spare parts, contactThis email address is being protected from spambots. You need JavaScript enabled to view it.
The webbing must be replaced periodically and/or in case of damage or wear.
WARNING: the webbing supplied by the company with the product is manufactured according to specific technical requirements and a defined breaking load. Replacing it with unsuitable or low-quality rope or webbing may cause accidents and serious injuries.
The webbing used to anchor the Flying Pole to the ceiling must be original or have suitable characteristics for human suspension (22kN).
For information and to purchase original spare parts, contact
4.1 SEPARATE THE POLE INTO TWO PARTS
Using the 5 mm Allen key, separate the pole into two parts by completely removing the internal joint:
WARNING: DO NOT TURN THE ALLEN KEY COUNTERCLOCKWISE TOO MANY TIMES, OTHERWISE THE STEEL PIN WILL COME OUT ON THE OPPOSITE SIDE AND LOCK THE JOINT. IF THIS HAPPENS, SCREW THE STEEL PIN CLOCKWISE WITH THE 5 MM ALLEN KEY UNTIL IT STOPS, THEN UNSCREW IT COUNTERCLOCKWISE BY ONLY 3 TURNS.
1° Place the pole horizontally on the ground before proceeding.
2° Using the 5 mm Allen key, unscrew the pin of the upper pole section counterclockwise by 3.5 turns.
3° Remove the Allen key and rotate the pole until you can see the two silver pins on the opposite side. Then use the Allen key to push inward the pin you have just unscrewed.
4° Separate the sections by gently pulling them apart.
The pole must slide out without force. If the section does not slide out, push the pin further inward. If it does not go in, screw the pin clockwise back into position and repeat the operation.
3° Remove the Allen key and rotate the pole until you can see the two silver pins on the opposite side. Then use the Allen key to push inward the pin you have just unscrewed.
4° Separate the sections by gently pulling them apart.
The pole must slide out without force. If the section does not slide out, push the pin further inward. If it does not go in, screw the pin clockwise back into position and repeat the operation.
WARNING: DO NOT TURN THE ALLEN KEY COUNTERCLOCKWISE TOO MANY TIMES, OTHERWISE THE STEEL PIN WILL COME OUT ON THE OPPOSITE SIDE AND LOCK THE JOINT. IF THIS HAPPENS, SCREW THE STEEL PIN CLOCKWISE WITH THE 5 MM ALLEN KEY UNTIL IT STOPS, THEN UNSCREW IT COUNTERCLOCKWISE BY ONLY 3 TURNS.
4.2 REMOVE THE UPPER END CAP
Slide off the pressure-fitted upper end cap of the pole.
4.3 UNSCREW AND REMOVE THE SPHERICAL LOWER END CAP
1° Using the 4 mm Allen key, unscrew the pin of the spherical end cap counterclockwise.
2° Slide off and separate the spherical end cap from the pole, with the webbing attached.
2° Slide off and separate the spherical end cap from the pole, with the webbing attached.
4.4 REMOVE THE SAFETY SLEEVE
Take the black safety sleeve with your fingers and slide it off completely.
4.5 UNSCREW ONLY ONE SCREW WITH THE 10 MM WRENCH OR WITH YOUR FINGERS
1° Lower the steel rope stopper.
2° Using the 10 mm wrench or your fingers, unscrew and remove only one screw.
2° Using the 10 mm wrench or your fingers, unscrew and remove only one screw.
4.6 REMOVE THE OLD WEBBING AND INSERT THE NEW ONE
1° Remove the old webbing.
2° Insert new webbing.
WARNING: the webbing supplied by the company with the product is manufactured according to specific technical requirements and a defined breaking load. Replacing it with unsuitable or low-quality rope or webbing may cause accidents and serious injuries. Do not hesitate to contact the company for original spare parts.
2° Insert new webbing.
WARNING: the webbing supplied by the company with the product is manufactured according to specific technical requirements and a defined breaking load. Replacing it with unsuitable or low-quality rope or webbing may cause accidents and serious injuries. Do not hesitate to contact the company for original spare parts.
4.7 SCREW THE SCREW BACK IN UNTIL IT STOPS
1° Using the 10 mm wrench or your fingers, screw the screw back in completely until it stops. Make sure to insert the wrench correctly into the screw head to prevent premature wear.
2° Use a pencil to check that the two screws are at the same height.
This check is very important for the safe use of the product and to allow the safety sleeve to be inserted correctly.
2° Use a pencil to check that the two screws are at the same height.
This check is very important for the safe use of the product and to allow the safety sleeve to be inserted correctly.
4.8 INSERT THE SAFETY SLEEVE
1° Make sure the screws are positioned as shown in the photo.
2° Insert the safety sleeve.
2° Insert the safety sleeve.
4.9 INSERT THE WEBBING INTO THE LOWER POLE SECTION AND SCREW ON THE SPHERICAL END CAP
1° Taking care not to twist the webbing inside the pole, insert it into the tube and feed it out from the opposite side.
2° Insert the spherical lower end cap into the tube, aligning the holes.
3° Using the 4 mm Allen key, tighten the spherical end cap by screwing it clockwise very firmly. Check before each use that the joint is properly tightened.
2° Insert the spherical lower end cap into the tube, aligning the holes.
3° Using the 4 mm Allen key, tighten the spherical end cap by screwing it clockwise very firmly. Check before each use that the joint is properly tightened.
4.10 PLACE THE WEBBING IN THE JOINT AND SCREW THE CENTRAL JOINT INTO THE LOWER SECTION
1° Taking care not to twist the webbing inside the pole, place it into the dedicated housings of the central joint.
2° Insert the joint into the lower pole section, aligning the holes.
3° Using the 5 mm Allen key, tighten the joint by screwing it clockwise very firmly. Check before each use that the joint is properly tightened.
2° Insert the joint into the lower pole section, aligning the holes.
3° Using the 5 mm Allen key, tighten the joint by screwing it clockwise very firmly. Check before each use that the joint is properly tightened.
4.11 JOIN THE POLE SECTIONS AND TIGHTEN THE CENTRAL JOINT SCREWS
1° Place the sections on the ground, insert the webbing into the second section and feed it out from the opposite side without twisting it.
2° Join the two pole sections, making sure to align the joint holes.
3° Using the 5 mm Allen key, tighten the joint to the upper part of the pole by screwing it clockwise very firmly. Check before each use that the joint is properly tightened.
4° Pull the webbing firmly.
WARNING! Before each use, check that all joints are properly tightened.
2° Join the two pole sections, making sure to align the joint holes.
3° Using the 5 mm Allen key, tighten the joint to the upper part of the pole by screwing it clockwise very firmly. Check before each use that the joint is properly tightened.
4° Pull the webbing firmly.
WARNING! Before each use, check that all joints are properly tightened.
4.12 INSERT THE WEBBING INTO THE UPPER END CAP OF THE POLE
1° Pull the webbing firmly and insert it into the hole of the upper end cap.
2° Insert the upper end cap into the pole.
2° Insert the upper end cap into the pole.
THE POLE IS ASSEMBLED. YOU CAN NOW PROCEED WITH INSTALLATION
Once the pole has been assembled, it can be installed by attaching it to the ceiling.
It is important to use a swivel to prevent the ropes from twisting.
GO TO SECTION: 5.0 FLYINGPOLE INSTALLATION
It is important to use a swivel to prevent the ropes from twisting.
GO TO SECTION: 5.0 FLYINGPOLE INSTALLATION
5.0 FLYINGPOLE INSTALLATION
The FlyingPole must be INSTALLED UNDER a suitable ceiling or suitable beams.
The ceiling must be at least 400 cm high.
Always use a swivel to prevent the ropes from twisting.
Follow the next section according to the ceiling anchor:
5.1 ATTACHING THE FLYINGPOLE TO THE CEILING WITH ALBATROS PLATE
5.2 ATTACHING THE FLYINGPOLE TO THE CEILING WITHOUT ALBATROS PLATE
5.1 ATTACHING THE FLYINGPOLE TO THE CEILING WITH ALBATROS PLATE
Accessories required to attach the pole to the ceiling WITH the Albatros plate, which already includes an integrated swivel:
2° Attach to the carabiner the rope or Daisy Chain, if needed, to reach the ceiling.
3° Attach the carabiner to the end of the rope or Daisy Chain.
4° Attach the carabiner to the shackle of the Albatros.
The length of the rope used to attach the FlyingPole to the ceiling depends on how far you want to keep it suspended from the ground.
For installations at greater heights, the use of crash mats is recommended.
For installation of the Albatros plate, read the relevant instructions included with the product.
- n° 1 rope or Daisy Chain to connect the FlyingPole to the ceiling.
- n° 2 carabiners.
2° Attach to the carabiner the rope or Daisy Chain, if needed, to reach the ceiling.
3° Attach the carabiner to the end of the rope or Daisy Chain.
4° Attach the carabiner to the shackle of the Albatros.
The length of the rope used to attach the FlyingPole to the ceiling depends on how far you want to keep it suspended from the ground.
For installations at greater heights, the use of crash mats is recommended.
For installation of the Albatros plate, read the relevant instructions included with the product.
5.2 ATTACHING THE FLYINGPOLE TO THE CEILING WITHOUT ALBATROS PLATE
Accessories required to attach the pole to the ceiling WITHOUT the Albatros plate:
2° Then attach the swivel to the carabiner.
3° Attach the second carabiner to the swivel.
4° Attach to the carabiner the rope or Daisy Chain, if needed, to reach the ceiling.
5° Attach the carabiner to the end of the rope or Daisy Chain.
6° Attach the carabiner to the ceiling hook.
The length of the rope used to attach the FlyingPole to the ceiling depends on how far you want to keep it suspended from the ground.
For installations at greater heights, the use of crash mats is recommended.
- n° 1 ceiling hook.
- n° 1 rope or Daisy Chain to connect the FlyingPole to the ceiling.
- n° 1 swivel, allowing the pole to rotate without twisting the ropes.
- n° 3 carabiners.
2° Then attach the swivel to the carabiner.
3° Attach the second carabiner to the swivel.
4° Attach to the carabiner the rope or Daisy Chain, if needed, to reach the ceiling.
5° Attach the carabiner to the end of the rope or Daisy Chain.
6° Attach the carabiner to the ceiling hook.
The length of the rope used to attach the FlyingPole to the ceiling depends on how far you want to keep it suspended from the ground.
For installations at greater heights, the use of crash mats is recommended.
6.0 POLE DISASSEMBLY: SEPARATING THE SECTIONS
Place the pole horizontally on the ground before proceeding.
1° Using the 5 mm Allen key, unscrew the pin of the upper section by 3.5 turns.
2° Rotate the pole until you can see the two silver pins, then use the Allen key to push inward the pin you have just unscrewed.
3° Slide the upper section out of the joint and rotate it, without twisting it, so that it lies next to the lower section.
WARNING: DO NOT TURN THE ALLEN KEY COUNTERCLOCKWISE TOO MANY TIMES, OTHERWISE THE STEEL PIN WILL COME OUT ON THE OPPOSITE SIDE AND LOCK THE JOINT. IF THIS HAPPENS, SCREW THE STEEL PIN CLOCKWISE WITH THE 5 MM ALLEN KEY UNTIL IT STOPS, THEN UNSCREW IT COUNTERCLOCKWISE BY ONLY 3 TURNS.
7.0 CHECKS BEFORE USE
7.1 Check BEFORE EACH USE that the joint or joints of the pole are always properly tightened.
7.2 Make sure BEFORE EACH USE that the rope is not damaged or worn. If it is, replace it immediately and DO NOT use the Flying Pole.
7.3 Make sure that all suspension accessories are suitable for the type of use.
7.4 Make sure that the equipment is used by experienced people and prepare any fall-protection safety accessories, such as protective mats.
7.2 Make sure BEFORE EACH USE that the rope is not damaged or worn. If it is, replace it immediately and DO NOT use the Flying Pole.
7.3 Make sure that all suspension accessories are suitable for the type of use.
7.4 Make sure that the equipment is used by experienced people and prepare any fall-protection safety accessories, such as protective mats.
8.0 WEBBING MAINTENANCE AND INSPECTION
8.1 The certified webbing installed inside the Flying Pole is the only connection system between the pole and the anchor point: if it breaks, the equipment and the performer will inevitably fall, with a high risk of damage to furniture, objects and people.
The condition and wear of the webbing must never be underestimated.
8.2 The webbing must be inspected along its entire length before and after each use, and its integrity must be verified and compatible with the execution of the performance or training session.
8.3 The lifespan of the webbing is 5 years + 1 year of storage. In any case, refer to the relevant technical data sheet.
8.4 To carry out the inspection: separate the pole by completely removing the central joint using the 5 mm Allen key.
8.5 Align the two sections, leaving approximately 10 cm of space between them: the visual inspection will take place through this “window”.
8.6 From the upper end, pull the webbing from one side only. The webbing will “rotate” inside the pole, allowing it to be inspected along its full length.
WARNING: The stitching of the webbing is positioned in the lower section and, due to its thickness, cannot pass through the safety attachment at the base of the pole. If resistance is felt while sliding the webbing during the previous step (8.6), reverse the direction of rotation of the webbing.
The condition and wear of the webbing must never be underestimated.
8.2 The webbing must be inspected along its entire length before and after each use, and its integrity must be verified and compatible with the execution of the performance or training session.
8.3 The lifespan of the webbing is 5 years + 1 year of storage. In any case, refer to the relevant technical data sheet.
8.4 To carry out the inspection: separate the pole by completely removing the central joint using the 5 mm Allen key.
8.5 Align the two sections, leaving approximately 10 cm of space between them: the visual inspection will take place through this “window”.
8.6 From the upper end, pull the webbing from one side only. The webbing will “rotate” inside the pole, allowing it to be inspected along its full length.
WARNING: The stitching of the webbing is positioned in the lower section and, due to its thickness, cannot pass through the safety attachment at the base of the pole. If resistance is felt while sliding the webbing during the previous step (8.6), reverse the direction of rotation of the webbing.
9.0 WARNINGS
9.1 The tools required for assembly, installation and disassembly are supplied. Before using different tools on the pole, contact the Technical Support Service to confirm that the operation is suitable.
9.2 During all stages of product assembly, installation and disassembly, always pay maximum attention and follow the instructions.
9.3 In case of doubt, contact support atThis email address is being protected from spambots. You need JavaScript enabled to view it.
9.4 Do not allow the product to be used, installed or handled by unqualified people or by minors unless supervised.
9.5 Since the product is sports equipment, it must be used by competent and trained people.
9.6 Do not perform unsupervised moves that you are not able to execute.
9.7 Use suitable protective equipment and certified mats.
9.8 The WLL of THEPOLE Flying Pole is 200 kg (2 people). When used as a Flying Pole, a safety factor of 8 is considered.
9.9 Make sure that the area of use of the Flying Pole is free from objects and obstacles.
9.10 Do not use the Flying Pole in any situation where adequate safety conditions are not guaranteed.
9.11 Do not use carabiners, ropes or webbing whose use has not been certified by the manufacturer for human use.
9.12 Before using the Flying Pole, make sure that the anchor point is stable.
9.13 Flying Pole and webbing must never be exposed to temperatures below -20°C or above 40°C.
AGMDESIGN.IT SHALL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE TO PROPERTY OR PERSONS CAUSED BY IMPROPER USE OF THE PRODUCT.
9.2 During all stages of product assembly, installation and disassembly, always pay maximum attention and follow the instructions.
9.3 In case of doubt, contact support at
9.4 Do not allow the product to be used, installed or handled by unqualified people or by minors unless supervised.
9.5 Since the product is sports equipment, it must be used by competent and trained people.
9.6 Do not perform unsupervised moves that you are not able to execute.
9.7 Use suitable protective equipment and certified mats.
9.8 The WLL of THEPOLE Flying Pole is 200 kg (2 people). When used as a Flying Pole, a safety factor of 8 is considered.
9.9 Make sure that the area of use of the Flying Pole is free from objects and obstacles.
9.10 Do not use the Flying Pole in any situation where adequate safety conditions are not guaranteed.
9.11 Do not use carabiners, ropes or webbing whose use has not been certified by the manufacturer for human use.
9.12 Before using the Flying Pole, make sure that the anchor point is stable.
9.13 Flying Pole and webbing must never be exposed to temperatures below -20°C or above 40°C.
AGMDESIGN.IT SHALL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE TO PROPERTY OR PERSONS CAUSED BY IMPROPER USE OF THE PRODUCT.
